Shop here
 [Up] 

Up

   #1 #2    #3     #4  

• Attach the switchbox #2 to a free COM port of your computer #1
• Make sure you have the right cable-diagram #3 for your radio = check for your specific radio!
• connect the data cable between switchbox #2 and radio #4
• connect audio cable between LINE-IN of #1 and AF-OUT of #4

If everything should fail =  READ the manual of your computer, your radio and RadioCom

To quick-install RadioCom   

• Write down the number (RC50 Key Nr) on your CD-ROM  "CI-xxxx-xxxx-xxxx-xxxx-xxxx"
• Insert CD-ROM into your CD-ROM drive
• If AUTORUN is activated the MAIN window of the CD-ROM will be displayed
• If the CD-ROM should not start automatically go to [CD-ROM-drive]:\ and run ServiceRC50.EXE.
• Enter your RC50 Key Number
• Select and open Section  <MANUAL> and select RC4 or RC5
• Double-click on Manual RadioCom    
• "Play" with the various sections on the CD-ROM.

#-2 Hardware

• Turn OFF your computer.

• Install the ISAC-switch-modem-adapter (switchbox), which comes with the software, to a free serial (COM) port of the computer).
• Then connect your radio according to the diagram ( refer to manual and to your CD-ROM under Section technical service )to the switchbox MALE PINS and to the sound card.
• sample diagram
• Do NOT use a regular serial cable (except for ICOM-PCR-1000 and IC-SWL switchbox)
• Do not forget your audio cable (i.e. Radio-AF OUT to LINE-IN of your sound card)

#3 Software

• Turn ON your radio.
• Turn ON your computer and start Windows, do not start any other application.
• Insert the RadioCom CD into your CD-ROM drive.
• If the CD should not start automatically go to [CD-drive]:\ and run ServiceRC50.exe
• Enter your RC50 Key Nr  
• Double-click on INSTALL RadioCom 5.2
• Follow the on-screen instructions to complete the installation.

• fatal error: no radio connected ,COM port not found or Bonito switchbox  not connected
  • make sure, that no other program is already using this COM port

• MICROSOFT VISUAL C++ RUNTIME LIBRARY  RUNTIME ERROR 
  • Your computer is missing the Microsoft Data Access Components (MDAC)
    You can find the latest version  at http://www.microsoft.com/data/download.htm
    and V.2.5 on the RadioCom CD under INSTALL > MDAC. Look for the English version mdac_typ_gb.exe .  
    Highlight that file and hit ENTER. It will install automatically.
•  
  • READ THIS:

  • Security Update for Microsoft Data Access Components

    November 20, 2002

    Why is this update needed?

    An identified security vulnerability could allow an attacker to compromise Microsoft® Windows®-based systems and then take any of a variety of actions, such as changing Web pages or reformatting your hard disk. You can help eliminate this issue by installing this update from Microsoft.

    Who needs to apply this update?

    Anyone using Microsoft Windows 2000, Windows Me, Windows 98 SE, Windows 98, or Windows NT® 4.0 needs the update. Windows XP is not affected by this issue. At greatest risk are systems that operate Web sites using Microsoft Internet Information Services (IIS) and anyone who browses the Web using Microsoft Internet Explorer.

    Two types of computers are at particular risk. If either of the following describes your computer, you should install the patch immediately:

    • Computers that are used to browse the Web or read e-mail. Most workstations and laptop computers fall into this category.
    • Computers that host Web sites using IIS.

    Which versions are eligible for the update?

    Updates are available for the following product versions. Earlier versions than those listed below are no longer supported and may or may not be affected by the vulnerability:

    • Windows NT® 4.0, Windows 98, Windows Me, Windows 2000
    • Microsoft Data Access Components (MDAC) 2.1, 2.5, 2.6
    • Internet Explorer 5.01, 5.5, 6.0

    Next Steps

    Ready to install the update? Choose the appropriate next step for you:

    • Get the update automatically with our Automatic Updates service.
    • To read more technical information about this vulnerability, see the full Microsoft Security Bulletin.

    Do I need this update?

    To determine if you need this update:

    1. On the taskbar at the bottom of your screen, click Start, then click Run.
    2. In the Run dialog box, type Winver and click OK.
       A dialog box displays the version of Windows your computer is running.
    3. Click OK to close the dialog box.

    If you are running Windows 98, Windows Millennium, Windows NT 4.0, or Windows 2000, you need to install this patch. If you are running Windows XP, you do not need the patch.